The Crown DCi 4/300DA DriveCore Install DA Series is a 4-channel power amplifier with Dante / AES67 networked audio and integrated DSP. The amplifier is capable of producing 300W of output per channel and works with 2-, 4-, 8-, and 16-Ohm speakers or with 70/100Vrms systems. Channels can be bridged for powering higher power applications such as a subwoofer.
The amp’s advanced capabilities and support for Dante Domain Manager makes it well suited for installations that are standardized on Dante for networked audio transport. The Dante / AES67 ports provide primary and secondary connections for redundancy and will accept 48 and 96 kHz digital audio. Analog audio can be sent via Dante / AES67 pre/post processing (at 48 kHz). Network configuration, monitoring, and control are provided with HiQnet protocols over standard TCP/IP network connections. The HiQnet Audio Architect software allows for remote configuration, monitoring, and control of all aspects of the DCi-DA Series amplifiers. Additionally, a programmable General Purpose Input/Output (GPIO) port can be configured to control volume, recall presets, report errors to a third-party control system, and more.
The integrated DSP provides a comprehensive set of tools and features including LevelMAX limiting for inputs and outputs with thermal limiting, input compression, input & output delay (up to 2 seconds), input & output EQ, crossover settings, and a signal generator. The Crown DCi 4/300DA DriveCore Install DA Series 4-Channel Amplifier ships with four input connectors and a power cord.
Features
- Crown’s proprietary and patented DriveCore technology
- Amplifiers are the next generation of PWM technology using high-quality, Class-D amplifier topologies
- Minimum Guaranteed Power Ratings: DCi amplifiers deliver the rated power in the specifications for long periods of time
- Direct Drive “Constant Voltage” capabilities on a channel by channel basis for 70 or 100Vrms amplification without the use of a step-up frequency limiting transformer for higher audio quality
- HiQnet Audio Architect supported amplifier
- Advanced PFC universal power supply provides efficiency, and is designed to deliver maximum power no matter where the amplifier is located; Universal AC input accepts 100 to 240 VAC, 50/60 Hz (±10%)
- DriveCore includes five patents that are also included in Crown’s flagship touring amplifier I-Tech HD4, providing versatility and durability
- TCP/IP based protocol in HiQnet for network monitoring and control
- Highly effective cooling system focuses airflow on parts that need it most, maximizing efficiency while minimizing heat and noise
- Integrated Dante / AES67 networked audio simplifies installation by enabling Dante / AES67 networked audio signals to be sent directly to the amplifier
Network monitoring and Control
- Continuous load monitoring
- Comprehensive error reporting
- Pilot tone monitoring
- Programmable general purpose input/output (GPIO) ports
Digital Signal Processing (DSP)
- LevelMAX: Limiters for inputs and outputs with thermal limiting
- Input compressor
- Input and output delay
- Input and output EQ
- Signal generator
- Crossover
Specifications
Inputs | 3-pin block connectors |
Outputs | Terminal strips |
Output Power | Dual Mode: @ 2 Ohms: 150 W (Per Channel) @ 4 Ohms: 300 W (Per Channel) @ 8 Ohms: 300 W (Per Channel) @ 16 Ohms: 150 W (Per Channel) @ 70 Vrms: 300 W (Per Channel) @ 100 Vrms: 300 W (Per Channel) Bridge Mono Mode: |
Voltage Gain | 34 dB |
Frequency Response | 20 Hz to 20 kHz (8 Ohms): ±0.25dB |
Signal to Noise Ratio | Signal to Noise Ratio (ref. rated power, (8 Ohms, 20 Hz to 20 kHz): > 108 dB |
Total Harmonic Distortion | < 0.35% (@ full-rated power, from 20 Hz to 20 kHz) |
Intermodulation Distortion | ≤ 0.35% (60 Hz and 7 kHz @ 4:1, from -30 dB to full-rated power) |
Damping Factor | > 1000 (20 to 100 Hz) |
Crosstalk | > 80 dB (below rated power, 20 Hz to 1 kHz) |
CMRR | > 70 dB (20 Hz to 1 kHz, typical) |
DC Output Offset | ±10 mV (with inputs shorted) |
Input Impedance | 10 kOhms (nominally balanced) 5 kOhms (nominally unbalanced) |
Maximum Input Level | +20 dBu (before compression) +26 dBu (before clipping) |
Required AC Mains | 100 to 240 VAC, 50/60 Hz (±10) |
Power Connector | 15 A IEC |
Cooling | Continuously variable-speed forced air, front-to-back airflow |
Load Impedance | Stereo/Dual Mode: 2 to 16 Ohms, 70 Vrms, 100 Vrms Bridged Mono: 4 to 16 Ohms, 140 Vrms, 200 Vrms |
Fan Noise Level | 45 |
Dimensions | 14.3″ / 36.2 cm |
Weight | 20.1 lb / 9.1 kg |
Package Weight | 25.475 lb |
Box Dimensions (LxWxH) | 22.1 x 20.7 x 8″ |
Reviews
There are no reviews yet.