System integrators working on challenging 21st century installed sound applications require equipment that is versatile, compact, and highly efficient. Look no further than the 4-channel Crown Audio DCI 4|600N, a 600W DriveCore Install BLU Link network amplifier with advanced features and flexibility. The amplifier provides analog and digital inputs, network monitoring and control, programmable General Purpose Input/Output (GPIO) ports, and on-board Digital Signal Processing (DSP). The amplifier also meets EN 54-16 compliance for life safety systems to serve the needs of hospitality, large venues, and other markets.
The 2 RU 4/600N can produce up to 600W of output per channel at 2, 4, 8 or 16 ohms or 70 or 100 Vrms. It is compatible with Harman’s BLU Link digital audio transport and accepts digital inputs via its rear-panel RJ-45 connectors. This digital control allows for networked monitoring, recallable presets, and the setup of secondary inputs that engage if the primary inputs fail. The built-in DSP capabilities include limiting, input/output EQs, delay, and a matrix mixer.
Each channel pair can be bridged for powering higher power applications such as a subwoofer. The 4|600N also has channel-independent high- or low-impedance output that is selectable from the rear-panel DIP switches. This allows you to integrate the amplifier into a variety of different setups. Each of its 4 channels additionally features independent attenuators with a range from 0 to -80 dB.
The front panel of the 4|600N provides a series of system indicators, including level and signal, ready, clip, thermal, and fault alerts for quick visual monitoring of the system. The unit can be integrated into a control system for powering on and off as well as engaging its sleep mode for saving energy when not in use.
Features
Network Monitoring & Control
Programmable General Purpose Input/Output Ports
DSP
Direct Drive Constant Voltage
Channel-Independent Hi-Z/Low-Z Selection
Bridgeable Channel Pairs
Remote On/Off Interface
Efficient Cooling Design
Auto Standby
TLC Protection
Advanced Protection Circuits
Specifications
Number of Channels | 4 |
Power Rating | 2 Ohms: 300 W per Channel 4 Ohms: 600 W per Channel 600 W Bridged 8 Ohms: 600 W per Channel 1200 W Bridged 16 Ohms: 300 W per Channel 1200 W Bridged 70 V / 100 V: 600 W per Channel 140 V / 200 V: 1200 W Bridged |
Load Impedance / Voltage | Parallel/Stereo: 2 / 4 / 8 / 16 Ohms 70 / 100 V Bridged/Mono: 4 / 8 / 16 Ohms 140 / 200 V |
Protections | DC Fault, Low Impedance, Overvoltage, Short Circuit, Thermal, Ultrasonic, Undervoltage |
Frequency Response | 20 Hz to 20 kHz ±0.25 dB |
Damping Factor | > 1000 |
Input Sensitivity | 1.4 Vrms (at 8 Ohms) 1.4 Vrms (at 70 V) 2 Vrms (at 100 V) |
Input Impedance | 10 Kilohms (Balanced) 5 Kilohms (Unbalanced) |
Max Gain | 34 dB |
SNR | > 104 dB (at 8 Ohms) > 108 dB (at 8 Ohms) |
THD | < 0.35% (Full Range, at Rated Power) |
Intermodulation Distortion | ≤ 0.35% |
Crosstalk | > 80 dB (Below Rated Power, 20 Hz to 1 kHz) |
CMRR | > 70 dB |
DSP | Yes |
Crossover | Yes |
Ducking/Muting | None |
Limiting | Yes |
I/O | 4 x Block 6-Pin Balanced Input 4 x Barrier Strip 4-Pin Output |
Digital I/O | 1 x RJ11 (Control) 1 x RJ45 (Control, Network) 2 x RJ45 BLU-Link |
USB | None |
AC Input Power | 100 to 240 VAC, 50 / 60 Hz |
AC Power Connector | 1 x IEC 15 A / NEMA 5-15 |
Current Consumption | 120 VAC: 2.7 to 4.1 A (1/8 Power) 5.6 to 9.5 A (1/3 Power) 230 VAC: 1.4 to 2.1 A (1/8 Power) 2.9 to 4.8 A (1/3 Power) |
Power Consumption | 120 VAC: 138 to 172 W (1/8 Power) 196 to 298 W (1/3 Power) 230 VAC: 141 to 178 W (1/8 Power) 176 to 269 W (1/3 Power) |
Display & Indicators | 15 x LED (Bridged Mode/Clip/Fault/Level/Signal/Standby/Thermal) |
Rackmount Size | 2 RU |
Cooling | Fan (Variable Speed) |
Thermal Dissipation | 1018 BTU/hr (Maximum) |
Dimensions | 19.0 x 3.5 x 14.3″ / 48.3 x 8.9 x 36.3 cm |
Weight | 20.1 lb / 9.1 kg |
Package Weight | 25.225 lb |
Box Dimensions (LxWxH) | 22.1 x 20.7 x 8″ |
Reviews
There are no reviews yet.