The Crown Audio DriveCore Install 2|2400N is a 2400W, 2-channel, BLU Link network amplifier with advanced features and flexibility that’s required by system integrators for challenging 21st century installed sound applications.
The 2/2400N can produce up to 2400W of output per channel at 2, 4, 8 or 16 ohms or 70 or 100 volts rms. It is compatible with Harman’s BLU Link digital audio transport and accepts digital inputs via its rear-panel RJ-45 connectors. This digital control allows for networked monitoring, recallable presets, and the setup of secondary inputs that engage if the primary inputs fail. The 2|2400N also has built-in DSP capabilities including limiting, input/output EQs, delay, and a matrix mixer.
Its two channels can be bridged for powering higher power applications such as a subwoofer. The 2|2400N also has channel-independent high- or low-impedance output that is selectable from the rear-panel DIP switches. This allows you to integrate the amplifier into a variety of different setups. Each of its 2 channels additionally features independent attenuators, ranging from 0 to -80 dB.
The front panel of the 2|2400N provides a series of system indicators, including level and signal, ready, clip, thermal, and fault alerts for quick visual monitoring of the system. The unit can be integrated into a control system for powering on and off as well as engaging its sleep mode for saving energy when not in use. The 2|2400N is rack-mountable and requires 2 RU of space. A 20A IEC power cord is included.
Features
Network Monitoring & Control
Programmable General Purpose Input/Output Ports
DSP
Direct Drive Constant Voltage
Channel-Independent Hi-Z/Low-Z Selection
Bridgeable Channel Pairs
Remote On/Off Interface
Efficient Cooling Design
Auto Standby
TLC Protection
Advanced Protection Circuits
Specifications
| Number of Channels | 2 |
| Power Rating | 2 Ohms: 2100 W per Channel 4 Ohms: 2400 W per Channel 4200 W Bridged 8 Ohms: 1900 W per Channel 4800 W Bridged 16 Ohms: 950 W per Channel 3800 W Bridged 70 V / 140 V: 2100 W per Channel 4200 W Bridged 100 V / 200 V: 2300 W per Channel 4600 W Bridged |
| Load Impedance / Voltage | Parallel/Stereo: 2 / 4 / 8 / 16 Ohms 70 / 100 V Bridged/Mono: 4 / 8 / 16 Ohms 140 / 200 V |
| Frequency Response | 20 Hz to 20 kHz ±0.25 dB (8 Ohms) |
| Damping Factor | > 5000 |
| Input Sensitivity | 2.5 Vrms (at 8 Ohms) 1.4 Vrms (at 70 V) 2 Vrms (at 100 V) |
| Input Impedance | 10 Kilohms (Balanced) 5 Kilohms (Unbalanced) |
| Max Gain | 34 dB |
| Max Input Level | +20 dBu |
| SNR | > 104 dB (at 8 Ohms) > 108 dB (at 8 Ohms) |
| THD | < 0.35% (Full Range, at Rated Power) |
| Intermodulation Distortion | ≤ 0.35% |
| Crosstalk | > 80 dB (Below Rated Power, 20 Hz to 1 kHz) |
| CMRR | > 70 dB |
| DSP | Yes |
| Crossover | Yes |
| Ducking/Muting | None |
| Limiting | Yes |
| I/O | 1 x Block 6-Pin Balanced Input 1 x Barrier Strip 4-Pin Output 1 x Block 8-Pin GPIO |
| Digital I/O | 1 x RJ45 Ethernet (Control, Network) 2 x RJ45 BLU-Link (I/O) |
| USB | None |
| AC Input Power | 100 to 240 VAC, 50 / 60 Hz |
| AC Power Connector | 1 x IEC 20 A / NEMA 5-20 |
| Current Consumption | 120 VAC: 4.5 to 10.7 A (1/8 Power) 9.2 to 23.6 A (1/3 Power) 230 VAC: 2.8 to 6.4 A (1/8 Power) 5 to 12.2 A (1/3 Power) |
| Power Consumption | 120 VAC: 239 to 523 W (1/8 Power) 286 to 881 W (1/3 Power) 230 VAC: 260 to 545 W (1/8 Power) 331 to 979 W (1/3 Power) |
| Display & Indicators | 15 x LED (Bridged Mode/Clip/Fault/Signal/Status/Thermal) |
| Rackmount Size | 2 RU |
| Cooling | Fan (Variable Speed) |
| Dimensions | 19.0 x 3.5 x 19.0″ / 48.3 x 8.9 x 48.3 cm |
| Weight | 24 lb / 10.9 kg |
No products in the cart. 
Reviews
There are no reviews yet.